Rich Color and a Finished Surface, Fast
Plain gray concrete is everywhere, and most of it looks unfinished. Patina is our decorative staining and sealing service, and it changes that quickly. We work color into the concrete you already have, then seal it for durability and a finished look. The surface goes from a flat, builder-grade slab to something with depth, warmth, and a deliberate finish, often in a single day.
Staining and sealing is the most direct way to make existing concrete look intentional. There is no demolition and nothing new to pour. We prepare the slab, color it, and protect it, and the space reads as designed rather than left over. For a floor, a patio, or a garage that has always looked temporary, it is a small project with an outsized effect.
Patina is a genuine craft finish, not a coat of paint. Paint sits on top of concrete and eventually peels; stain works into the surface to color the concrete itself, so it looks natural and wears far better. Sealed over the top, the result holds up to daily traffic and cleans up easily, and it keeps looking its best with nothing more than routine care.
Why Staining and Sealing Is Worth It
Staining and sealing gives you the biggest visible change for the least disruption of anything we do. It is the finish to reach for when the concrete is sound but the space looks unfinished, and you do not want the cost or timeline of a full overlay or a new pour.
- Usually finished in one to two days, so the space is back in use quickly
- Works with the concrete you already have — no demolition, no new pour
- Color that lives in the surface, not a film that peels off the top
- A sealed finish that resists everyday traffic and wipes clean
- A dramatic improvement in how a floor, patio, or garage reads
Where Patina Works
Almost any sound concrete surface is a candidate. Staining and sealing suits both the inside of the home and the outdoor and utility spaces that usually get ignored.
- Interior floors — basements, living spaces, sunrooms, and finished lower levels
- Patios, porches, and covered outdoor living areas
- Garage floors that deserve better than bare gray concrete
- Entryways, mudrooms, and utility spaces
- Commercial and light-retail floors where a clean, finished look matters
How We Install It
Even a one-day project rewards careful work. The finish is only as good as the preparation and the hand that applies the color, and we do not rush either.
- Assess the concrete. Lafayette looks at the slab, checks that it is sound, and confirms staining and sealing is the right call before quoting.
- Clean and prepare. We deep-clean the surface and address anything that would keep the stain from taking evenly, so the color lands the way it should.
- Apply the color. Stain is worked into the concrete by hand, building depth and movement rather than a flat, uniform coat.
- Detail the finish. We refine the color and tone until the surface reads the way you want it, matched to the room or the setting.
- Seal. The surface is sealed for durability and the right level of sheen, protecting the color and making the floor easy to keep clean.
- Walk it together. We review the finished surface with you before the job is called done.
Color, Tone, and Sheen
Stained concrete has a natural, variegated character that a solid coating cannot match. Because the color settles into the surface unevenly by design, the finished floor has depth and movement, closer to natural stone than to paint. We tune the color and the tone with you, and we set the sheen at seal time, from a low, matte finish to a richer, more polished look, depending on the space and how you want it to feel.
If you are working with a designer or matching a broader palette, we choose the color on your property, in the light the surface actually lives in, rather than off a chip in a showroom. The goal is a floor that looks like it was meant for the room.
Where Patina Fits Among Our Finishes
Patina is the lightest-touch finish we offer, and that is its strength. It does not rebuild the surface the way microcement or an exterior overlay does; it takes the concrete you have and makes it look finished. That makes it the right answer when the slab is sound, the look is the problem, and speed matters.
For a lot of clients it is also the natural starting point. Stain and seal a basement or a patio, live with it, and see how the space feels finished. If you later want the smooth, hand-troweled, joint-free look of interior microcement or a full exterior resurfacing, we can talk about that when the time is right. There is no pressure to do everything at once, and staining is a low-commitment way to see the quality of our work firsthand before a larger project. Many clients start with a single stained floor and come back for microcement once they have seen how we finish and how we treat their home.
A Fast Win Before a Bigger Project
Timing is part of why staining and sealing is so useful. Because it usually wraps in a day or two, it slots neatly into the end of a renovation, the run-up to putting a house on the market, or the stretch before hosting. A finished basement floor or a clean, colored garage can be the last thing that makes a space feel done, and it does not hold up the rest of your plans to get it. We can often get a Patina project on the calendar quickly and out of your way just as fast. Because the disruption is minimal and the payoff is immediate, it is one of the few upgrades where you see the full result almost as soon as the work is done, with no long cure or weeks of waiting before the space is usable again.
How It Holds Up and How to Care for It
Because the color is in the concrete and protected by sealer, a Patina finish stands up to daily traffic, furniture, and regular cleaning. The sealer is the wear layer, and it is refreshed on a simple schedule we lay out for your specific surface and how hard it gets used. Care in between is easy: keep it clean, wipe up spills, and let us refresh the sealer when it is due. Sealed and maintained normally, the finish keeps looking its best for years.
Built for Middle Tennessee Homes
We work in and around Nashville every week, in Brentwood, Belle Meade, Forest Hills, Franklin, Green Hills, and the surrounding counties. Staining and sealing is a fast, high-value way to finish a space, and because the work is close, scheduling is flexible and the follow-up is quick. The same craftsman who priced your floor is the one applying the color, start to finish. More than 100 five-star reviews across Middle Tennessee are the record of how we treat the work and the people we do it for.
For Builders, Remodelers, and General Contractors
If you are a general contractor, project manager, or high-end remodeler, Patina is the easiest way to start working with us. It is fast, clean, and low-risk, which makes it a natural first project. You get to see how we run a job, how we communicate, and how we leave a site, without committing to a larger microcement or resurfacing scope up front. For many trade partners a staining and sealing job is the door-opener that turns into repeat work across projects, because the finish holds up and the process makes you look good in front of your client. We coordinate around your schedule and are glad to walk a space with you and spec the finish before you price it.